国产三级伦理在线,久久久久黄久久免费漫画,成人国产精品日本在线,欧美美最猛性xxxxxx

我們的優勢是歐美進口備件配件，所有進口的冷門的停產的或者你們找不到

的產品都可以來找我！

美國西門子ITE全系列、EATON電機 斷路器  接觸器 變壓器 、 GE電氣 斷路

器 接觸器 變壓器 、 Cutler-Hammer（卡特拉-漢莫）、艾默生電機、PQ、

VERSA  這些品牌我們價格都很美好。

歡迎前來詢價！


廈門紀揚科技有限公司是一家以工業自動化為主營，融科、工、貿于一體，

專業從*工業自動化工程項目設計、安裝、調試等服務和*銷售各類進口**

電氣及自動化產品的民營高新技術企業。綜合型的工程技術服務型單位，是

國內專業的電氣產品分銷商及工業自動化系統集成商。

主營：世界知名品牌的PLC 、DCS 系統備件 模塊

①Allen-Bradley(美國AB)系列產品》

②Schneider(施耐德電氣)系列產品》

③General electric(通用電氣)系列產品》

④Westinghouse（美國西屋）系列產品》

⑤SIEMENS(西門子系列產品)》

⑥銷售ABB Robots. FANUC Robots、YASKAWA Robots、KUKA Robots、Mitsubishi Robots、OTC Robots、Panasonic Robots、MOTOMAN Robots。

⑦estinghouse（西屋）： OVATION系統、WDPF系統、MAX1000系統備件。

⑧Invensys Foxboro（福克斯波羅）：I/A Series系統，FBM（現場輸入/輸出模塊）順序控制、梯形 邏輯控制、事故追憶處理、數模轉換、輸入/輸出信號處理、數據通信及處理等。Invensys Triconex: 冗余容錯控制系統、基于三重模件冗余（TMR）結構的zui現代化的容錯控制器。

⑨Siemens(西門子)：Siemens MOORE， Siemens Simatic C1，Siemens數控系統等。

⑩Bosch Rexroth（博世力士樂）：Indramat，I/O模塊,PLC控制器,驅動模塊等。

◆Motorola（摩托羅拉）：MVME 162、MVME 167、MVME1772、MVME177等系列。

Bender CME420-D-1

 
Serial ports Com1 through Com3 are configured by default for RS-232. For 
further details or instructions on how to configure these ports to RS- 422/485, 
see Appendix A. 
3.4.6 GC-Printer wiring
A printer can be connected directly to the GC the field termination board 
(FTB) at one of the serial ports. The type and scheduling of reports 
produced at the GC printer are determined by settings made in 
MON2000 (from the Reports menu, select GC Report Request and/or GC 
Printer Control; see the MON2000 Software for Gas Chromatographs User 
Manual (P/N 3-9000-522) for more information).
Note
The GC uses only a generic printer driver. The PC printer allows more control and better 
quality output. 
To connect a printer to the GC serial port:
1. Access the GC FTB (see Figure 3-20 in "Section 3.4.2: Preparing for 
serial connections").
Model 700 Gas Chromatograph System Reference Manual
APRIL 2012 3-9000-521
3 - 47
2. Choose an available serial port on the FTB that is configured for 
RS-232 serial protocol.
Note
See Appendix A for a complete listing of the serial ports and corresponding 
pinouts to fabricate a serial printer cable. 
3. After the wiring connections have been completed, use 
MON2000 to configure the GC serial port.
(a.) From the Application menu, select Serial Ports. The Serial 
Ports window appears.
(b.) Select the appropriate Port row and set Usage to “Report”, 
Protocol to “ASCII” and RW to “W”. 
(c.) Ensure that the Com ID setting is correct.
(d.) Leave all other settings at the default values (see the 
MON2000 User Manual for more information).
3.4.7 Discrete digital I/O wiring
The Field Termination Board (P/N 3-0700-010) has five discrete outputs 
and four discrete inputs. Refer to the MON2000 Software for Gas 
Chromatographs Manual (P/N 3-9000-522) and use the Application>User 
Defined>Selection menu to to configure the Digital Outputs.
System Reference Manual Model 700 Gas Chromatograph
3-9000-521 APRIL 2012
3 - 48
Note
Configure the Digital Output using the MON2000 Software, from the Application > 
User Defined>Selections, set the enable the Common Alarm either Normally Open or 
Normally Closed.
3.4.7.1 Discrete digital inputs
To connect digital signal input/output lines to the GC (P/N 3-0700-010):
1. Access the FTB (see Figure 3-31)
(P/N 3-0700-010). 
Model 700 Gas Chromatograph System Reference Manual
APRIL 2012 3-9000-521
3 - 49
Figure 3-31. Field termination board
The FTB has five discrete outputs and four discrete inputs. The 
discrete input, DIG_IN4, is dedicated to a pressure switch. The 
discrete inputs are located on J10 (10 pin Phoenix connector).
2. Route digital I/O lines appropriately, especially in the case of the 
explosion-proof enclosure.
There are connections for four digital inputs and five digital 
output lines (Phoenix 10-pin connector), as follows:
Table 3-3. FTB discrete digital inputs
J10 Function Description
Pin 1 DIG_IN1
Pin 2 GND
Pin 3 DIG_IN2
Pin 4 GND
Pin 5 DIG_IN3 to customer