国产三级伦理在线,久久久久黄久久免费漫画,成人国产精品日本在线,欧美美最猛性xxxxxx

我們的優勢是歐美進口備件配件，所有進口的冷門的停產的或者你們找不到

的產品都可以來找我！

美國西門子ITE全系列、EATON電機 斷路器  接觸器 變壓器 、 GE電氣 斷路

器 接觸器 變壓器 、 Cutler-Hammer（卡特拉-漢莫）、艾默生電機、PQ、

VERSA  這些品牌我們價格都很美好。

歡迎前來詢價！


廈門紀揚科技有限公司是一家以工業自動化為主營，融科、工、貿于一體，

專業從*工業自動化工程項目設計、安裝、調試等服務和*銷售各類進口**

電氣及自動化產品的民營高新技術企業。綜合型的工程技術服務型單位，是

國內專業的電氣產品分銷商及工業自動化系統集成商。

主營：世界知名品牌的PLC 、DCS 系統備件 模塊

①Allen-Bradley(美國AB)系列產品》

②Schneider(施耐德電氣)系列產品》

③General electric(通用電氣)系列產品》

④Westinghouse（美國西屋）系列產品》

⑤SIEMENS(西門子系列產品)》

⑥銷售ABB Robots. FANUC Robots、YASKAWA Robots、KUKA Robots、Mitsubishi Robots、OTC Robots、Panasonic Robots、MOTOMAN Robots。

⑦estinghouse（西屋）： OVATION系統、WDPF系統、MAX1000系統備件。

⑧Invensys Foxboro（福克斯波羅）：I/A Series系統，FBM（現場輸入/輸出模塊）順序控制、梯形 邏輯控制、事故追憶處理、數模轉換、輸入/輸出信號處理、數據通信及處理等。Invensys Triconex: 冗余容錯控制系統、基于三重模件冗余（TMR）結構的zui現代化的容錯控制器。

⑨Siemens(西門子)：Siemens MOORE， Siemens Simatic C1，Siemens數控系統等。

⑩Bosch Rexroth（博世力士樂）：Indramat，I/O模塊,PLC控制器,驅動模塊等。

◆Motorola（摩托羅拉）：MVME 162、MVME 167、MVME1772、MVME177等系列。

SMN11071319   

 
Note
The first stream is the calibration gas stream.
- Carrier gas is fed from two bottles.
- When one bottle is nearly empty (100 psig), the other 
bottle becomes the primary supply.
- Each bottle can be disconnected for refilling without 
interrupting GC operation.
3. Connect calibration standard gas to the GC
Note
When installing the calibration standard gas line, ensure that the correct 
tubing connection is made. 
? Use 1/8-inch stainless steel tubing to conduct calibration 
standard gas.
? Use a single-stage regulator with low-side capacity of up to 30 
psig.
? The calibration gas inlet is the last inlet following the sample 
gas.
Model 700 Gas Chromatograph System Reference Manual
APRIL 2012 3-9000-521
3 - 29
Figure 3-13. Calibration gas stream inlet (right side of unit)
4. Connect sample gas stream(s) to the GC (see Figure 3-11 Model 
700 Upper Enclosure panel).
? Use 1/8-inch or 1/4-inch stainless steel tubing to conduct 
calibration standard gas.
? Ensure that pressure of sample line is regulated to maintain 15 
to 30 psig (±10%).
? Gas stream inlet(s) are identified (see Figure 3-14) for details.
 Gas Inlet
Calibration
System Reference Manual Model 700 Gas Chromatograph
3-9000-521 APRIL 2012
3 - 30
Figure 3-14. Sample stream inlets (Right side of unit)
5. After all lines have been installed, proceed with leak checking the 
carrier and sample lines. See Section 3.5.1; note that it requires 
the AC power to be turned on at the GC.
3.4 Setting the Com ID
The Model 700 Com ID is determined by dual inline package (DIP) switch 
settings.
Note
Follow the steps in this section only if you wish to change the Com ID setting or visually 
inspect and verify the DIP switch settings. 
 Streams 1 - 7
 Gas Inlets Gas Inlet
Calibration
Model 700 Gas Chromatograph System Reference Manual
APRIL 2012 3-9000-521
3 - 31
Figure 3-15. Dip switch
In most cases, the Com ID configuration made at the factory will not 
need to be changed. The factory DIP switch settings produce a Com ID of 
1.
3.4.1 Inspect or change the Com ID
To visually inspect and verify the DIP switch settings or to change the 
Com ID settings on the multifunction board,
1. Remove the dome from the upper enclosure.
CAUTION
Use caution when accessing an enclosure. A voltage of 115 to 230 VAC, along with 
various DC voltages, are present. Failure to follow this precaution may cause injury to 
personnel or damage equipment. 
2. Loosen the thumb screws on the oven system mounting plate.
Note
Note that MON2000 Com I.D. settings will override the hardware settings. To 
use the hardware Com I.D. configuration, enter a zero in the MON2000 Com 
I.D. settings. For details, refer to MON2000 Software for Gas Chromatographs 
User Manual (P/N 3-9000-522).