国产三级伦理在线,久久久久黄久久免费漫画,成人国产精品日本在线,欧美美最猛性xxxxxx

我們的優勢是歐美進口備件配件，所有進口的冷門的停產的或者你們找不到

的產品都可以來找我！

美國西門子ITE全系列、EATON電機 斷路器  接觸器 變壓器 、 GE電氣 斷路

器 接觸器 變壓器 、 Cutler-Hammer（卡特拉-漢莫）、艾默生電機、PQ、

VERSA  這些品牌我們價格都很美好。

歡迎前來詢價！


廈門紀揚科技有限公司是一家以工業自動化為主營，融科、工、貿于一體，

專業從*工業自動化工程項目設計、安裝、調試等服務和*銷售各類進口**

電氣及自動化產品的民營高新技術企業。綜合型的工程技術服務型單位，是

國內專業的電氣產品分銷商及工業自動化系統集成商。









主營：世界知名品牌的PLC 、DCS 系統備件 模塊

①Allen-Bradley(美國AB)系列產品》

②Schneider(施耐德電氣)系列產品》

③General electric(通用電氣)系列產品》

④Westinghouse（美國西屋）系列產品》

⑤SIEMENS(西門子系列產品)》

⑥銷售ABB Robots. FANUC Robots、YASKAWA Robots、KUKA Robots、Mitsubishi Robots、OTC Robots、Panasonic Robots、MOTOMAN Robots。

⑦estinghouse（西屋）： OVATION系統、WDPF系統、MAX1000系統備件。

⑧Invensys Foxboro（�？怂共�羅）：I/A Series系統，F(xiàn)BM（現場輸入/輸出模塊）順序控制、梯形 邏輯控制、事故追憶處理、數模轉換、輸入/輸出信號處理、數據通信及處理等。Invensys Triconex: 冗余容錯控制系統、基于三重模件冗余（TMR）結構的zui現代化的容錯控制器。

⑨Siemens(西門子)：Siemens MOORE， Siemens Simatic C1，Siemens數控系統等。

⑩Bosch Rexroth（博世力士樂）：Indramat，I/O模塊,PLC控制器,驅動模塊等。

◆Motorola（摩托羅拉）：MVME 162、MVME 167、MVME1772、MVME177等系列。

道依茨 4070017

 
1. Slowly pressurize the Sample line (up to 20 psig).
2. Block-in the line.
3. Observe the regulator, making sure the pressure holds. The 
pressure should not decrease for a period of two to three 
minutes.
4. When the GC passes the “Initial Sample Gas leak check”, re-open 
the Sample Gas lines.
3.5.2 Purging carrier gas lines
Purging carrier and calibration gas lines requires AC power. Use Helium 
that is 99.995% pure and that has less than 5ppm water and less than 
0.5ppm hydrocarbons.
Note
Tubing should be clean and dry internally. During installation, the tubing should have 
been blown free of internal moisture, dust, or other contaminants. 
To purge the carrier gas lines,
1. Ensure that the MV vent line plug has been removed, and the vent 
line is open. 
2. Ensure that the carrier gas bottle valve is open.
3. Set the carrier gas line pressure at 110 psig. Use the dual stage 
regulator at the carrier gas bottle to adjust pressure.
Note
Do not use the “Carrier Pressure Adjust” regulator adjustment (on the Flow Panel 
Assembly) to adjust carrier gas line pressure. This pressure is factory-set and should not 
be adjusted. 
System Reference Manual Model 700 Gas Chromatograph
3-9000-521 APRIL 2012
3 - 58
4. Turn ON the AC power to the GC.
5. Establish communications with the GC via the MON2000 
software. (Use the File > Quick Connect menu path; see Section 
2.7.2 in the MON2000 Software for Gas Chromatographs User 
Manual (P/N 3-9000-522) for more information.)
6. Use the Applications>Temperature Control menu path to access this 
function. The readouts of the block, column and SSS heater 
controllers should indicate that the unit is warming up. Also, the 
yellow and red status indicators on the FTB4 should be on.
7. Allow the GC system temperature to stabilize and the Carrier Gas 
lines to become fully purged with Carrier Gas.
8. Select the Auto Sequence Function. Use the Control > Auto 
Sequence menu path described in Section 4 of the MON2000
Software for Gas Chromatographs User Manual (P/N 3-9000-522).
Note
A period of 4 to 8 hours (or overnight) is recommended, during which all of the 
settings described in Steps 1 through 7 are maintained. No other settings 
should be made.
3.5.3 Purging calibration gas lines
To purge the calibration gas lines, as preparation for first calibration:
1. Ensure that the Carrier Gas lines have been fully purged, as 
described in the previous section, and that the SV plug has been 
removed.
2. Close the calibration gas bottle valve.
3. Fully open the block valve associated with calibration gas feed 
(the block valve should be located on lower right-hand corner of 
the front panel).
See Section 5.8 in the MON2000 Software for Gas Chromatographs 
User Manual (P/N 3-9000-522) for instructions on selecting 
streams.
Model 700 Gas Chromatograph System Reference Manual
APRIL 2012 3-9000-521
3 - 59
4. Open the calibration gas bottle valve.
5. At the calibration gas bottle regulator, increase outlet pressure to 
20 psig, ±5%.
6. Close the calibration gas bottle valve.
7. Let both gauges on the calibration gas bottle valve bleed down to