国产三级伦理在线,久久久久黄久久免费漫画,成人国产精品日本在线,欧美美最猛性xxxxxx

    G3-GM10-M0800電子系統
    發布者:上海凌亮光電科技有限公司  發布時間:2023-02-04 14:38:38  訪問次數:264

            CLK_IN input frequency must be in the range 5 to 60 MHz. Out of this range, the performances may be decreased. In case of multi-cameras synchronization (means more than one camera on one acquisition board):

           ? the "master" camera will provide DATA, STROBE and LVAL signals to the acquisition board. The others will only provide DATA. 

          ? the external clock CLK_IN must be input on each cameras to guaranty perfect data synchronization. 

          ? the trigger(s) input (TRIG1 and/or TRIG2) must be input on each cameras. It is recommended to synchronize the rising edge of these signals on the CLK_IN falling edge.

          ? cables must be balanced between each cameras (same quality, same length) to ensure perfect cameras synchronization. 

          ? the CLK_IN frequency must be equal to the two CCD register frequency. It means that the user shall use either H=2 (2 taps at CLK_IN data rate) or H=10 (1 tap at 2xCLK_IN data rate). Using H=1 clock mode will provide LVAL jitter on the "slave" camera. 

         ? Only "triggered and integration time controlled" (M=3 or M=4) can be used. These modes ensure perfect readout phase starting for each cameras. 

         Electrical Interface 9.1 Power Supply It is recommended to insert a 1A fuse between the power supply and the camera. I = input, O = output, I/O = bidirectional signal, P = power/ground, NC = not connected 9.2 Camera Control The Camera Link interface provides four LVDS signals dedicated to camera control (CC1 to CC4). On the AViiVA, three of them are used to synchronize the camera on external events. I = input, O = output, I/O = bidirectional signal, P = power/ground, NC = not connected Note: CC3 is not used. 9.3 Video Data Data and enable signals are provided on the Camera Link interface. I = input, O = output, I/O = bidirectional signal, P = power/ground, NC = not connected Table 9-1. Power Supply Signal Name I/O Type Description PWR P – DC power input: +12V to +24V (±0.5V) GND P – Electrical and Mechanical ground Table 9-2. Camera Control Signal Name I/O Type Description TRIG1 I RS644 CC1 – Synchronization input (refer to “Synchronization Mode” on page 6) TRIG2 I RS644 CC2 – Start Integration period in dual synchro mode (refer to “Synchronization Mode” on page 6) CLK_IN I RS644 CC4 – External clock for (multi-)camera synchronization (refer to “Synchronization Mode” on page 6) Table 9-3. Video Data Signal Name I/O Type Description ODD[11-0] O RS644 Odd pixel data (refer to “Output Data Timing” on page 8), ODD-00 = LSB, ODD-11 = MSB EVEN[11-0] O RS644 Even pixel data (refer to “Output Data Timing” on page 8), EVEN-00 = LSB, EVEN-11 = MSB STROBE O RS644 Output data clock (refer to “Output Data Timing” on page 8), data valid on the rising edge LVAL O RS644 Line valid (refer to “Output Data Timing” on page 8), active high sign

免責聲明:焊材網轉載作品均注明出處,本網未注明出處和轉載的,是出于傳遞更多信息之目的,并不意味 著贊同其觀點或證實其內容的真實性。如轉載作品侵犯作者署名權,或有其他諸如版權、肖像權、知識產權等方面的傷害,并非本網故意為之,在接到相關權利人通知后將立即加以更正。聯系電話:0571-87774297。
0571-87774297  
主站蜘蛛池模板: 五台县| 化州市| 称多县| 林甸县| 黑河市| 寻乌县| 营山县| 英山县| 攀枝花市| 茌平县| 龙川县| 涿鹿县| 岱山县| 那坡县| 沂南县| 五莲县| 巨野县| 芒康县| 嘉祥县| 南通市| 闻喜县| 松原市| 鄂尔多斯市| 磐石市| 自治县| 冷水江市| 明星| 富平县| 阳东县| 陇南市| 基隆市| 芜湖市| 云林县| 浦城县| 永城市| 海盐县| 铁力市| 卢湾区| 磐石市| 丰顺县| 淮南市|