国产三级伦理在线,久久久久黄久久免费漫画,成人国产精品日本在线,欧美美最猛性xxxxxx

    CR-GM00-M128x半導體
    發布者:上海凌亮光電科技有限公司  發布時間:2023-02-04 14:20:45  訪問次數:183

            Camera Command and Control Camera configuration is set through the serial interface. Please refer to “Serial Communication” on page 11 for the detailed protocol of the serial line. Note: 

            1. e2v commends to use E = 1 because of the limited EEPROM write cycles refer on page 12. 

            2. Camera gain (dB) = G x 0.047. A and B gain value are set in manufacturing but can be adjust if necessary. 

            3. Commands “H=2” and “H=4” will give 10 and 15 MHz data rate which are not compatible with Camera Link standard. Please don’t use it.

            4. The pinout corresponding to this option is fully compatible with the Camera Link standard. Table 7-1. Camera Command and Control Setting Command Parameter Description Configuration record(1) E= 0 1 The camera configuration is recorded on each change The camera configuration is recorded only on request Gain(2) G= 0 to 851 Gain setting from 0 to 40 dB (~0.047dB steps) Even Gain(2) A= 0 to 20 Even pixels gain adjustment (odd – even mismatch adjustment) Odd Gain(2) B= 0 to 20 Odd pixels gain adjustment (odd – even mismatch adjustment) Data transfer(3) H= 0 1 3 5 6 7 8 9 10 Two outputs on external clock One output (multiplexed) on external clock One output (multiplexed) at 20 MHz data rate One output (multiplexed) at 30 MHz data rate Two outputs at 20 MHz data rate One output (multiplexed) at 40 MHz data rate Two outputs at 30 MHz data rate One output (multiplexed) at 60 MHz data rate One output (multiplexed) on external clock (data frequency / 2)(7) Output format(4) S= 0 1 2 12-bit Output data 10-bit Output data 8-bit Output data Pattern(5) T= 0 1 Standard Test pattern Integration Time I= 5 to 13000 Integration time (μs) in free run or external triggered mode Trigger mode M= 1 2 3 4 Free run with integration time setting (see Figure 8-1) External trigger with integration time setting (see Figure 8-2) Trigger and Integration time

            controlled (see Figure 8-3) Trigger and integration time controlled by two inputs (see Figure 8-4) Even data Offset(6) O= 0 to 15 Even Offset setting from 0 to approx. 200 LSB Odd data Offset(6) P= 0 to 15 Odd Offset setting from 0 to approx. 200 LSB Special commands != 0 1 2 3 4 5 Camera identification readout User camera identification readout Software version readout Camera configuration readout Current camera configuration record Default camera configuration restoration User camera ID $= String of Char. Writing and record of the user camera identification

            5. The test pattern is useful to check if the interfacing is well done. The user should see a jagged image of 256 pixels steps. 

            6. The offset is set in manufacturing to balance both the channels. The initial setting is about 8 (~ 130 LSB). In some cases, the user may have to change it (for example if the ambient temperature is very high). 

            7. To be used for multi-camera synchronization. R

免責聲明:焊材網轉載作品均注明出處,本網未注明出處和轉載的,是出于傳遞更多信息之目的,并不意味 著贊同其觀點或證實其內容的真實性。如轉載作品侵犯作者署名權,或有其他諸如版權、肖像權、知識產權等方面的傷害,并非本網故意為之,在接到相關權利人通知后將立即加以更正。聯系電話:0571-87774297。
0571-87774297  
主站蜘蛛池模板: 和龙市| 瑞安市| 千阳县| 宣化县| 石首市| 桦甸市| 防城港市| 普宁市| 观塘区| 苍山县| 衢州市| 侯马市| 沁源县| 康平县| 襄垣县| 新密市| 大厂| 崇左市| 如皋市| 云南省| 乌拉特中旗| 山阳县| 岫岩| 新津县| 延川县| 师宗县| 呼图壁县| 兴仁县| 冷水江市| 海丰县| 沁源县| 清原| 莱西市| 邯郸县| 秦皇岛市| 阆中市| 金门县| 石柱| 天水市| 肇庆市| 南平市|