国产三级伦理在线,久久久久黄久久免费漫画,成人国产精品日本在线,欧美美最猛性xxxxxx

    EV71YEM4CL2014-BA0物流業
    發布者:上海凌亮光電科技有限公司  發布時間:2023-02-03 17:03:04  訪問次數:134

         Signal Name I/O Type Description TRIG1 I RS644 CC1 – Synchronization input (refer to “Synchronization Mode” on page 6) TRIG2 I RS644 CC2 – Start Integration period in dual synchro mode (refer to “Synchronization Mode” on page 6) CLK_IN I RS644 CC4 – External clock for (multi-)camera synchronization (refer to “Synchronization Mode” on page 6)

         Signal Name I/O Type Description ODD[11-0] O RS644 Odd pixel data (refer to “Output Data Timing” on page 8), ODD-00 = LSB, ODD-11 = MSB EVEN[11-0] O RS644 Even pixel data (refer to “Output Data Timing” on page 8), EVEN-00 = LSB, EVEN-11 = MSB STROBE O RS644 Output data clock (refer to “Output Data Timing” on page 8), data valid on the rising edge LVAL O RS644 Line valid (refer to “Output Data Timing” on page 8), active high signa

        Note: Notes:FVAL, as defined in the Camera Link standard, is not used. FVAL is permanently tied to 0 (low) level. DVAL is not used. DVAL is permanently tied to 1 (high) level. In case of Single output, the data (multiplexed) are output in place of Odd data. 9.4 Serial Communication The Camera Link interface provides two LVDS signal pairs for the communication between the camera and the frame grabber. This is an asynchronous serial communication based on RS-232 protocol. The configuration of the serial line is: 

        ? Full duplex/without handshaking

        ? 9600 bauds, 8-bit data, no parity bit, 1 stop bit.

        Command Syntax The valid syntax is "S = n(CR)" with:

        ? S: command identification as per “Camera Command and Control” on page 5. S is a single character in upper case. 

        ? n: setting value. 

        ? (CR): means "carriage return". no space, nor tab may be inserted between S, =, n and (CR). Example of a valid command: 

        ? G = 3(CR): sets the camera to gain 3 (refer to “Camera Command and Control” on page 5 for exact value calculation). Example of non valid commands: ? G = 3(CR): spaces ? g = 3(CR): g instead of G ? G = 1040(CR): 1040 is outside of range 9.4.2 Command Processing Each command received by the camera is processed: ? If the command is valid: – the setting is done in case of a write command. – the camera returns the data separated by (CR) in case of the read command. – the camera returns: >OK(CR). ? If the command is not valid: – nothing is done. – the camera returns: >1 = out of range; >2 = syntax error; >3 = command too long; >4,>6,>7 = internal error; >5 undefined function.

免責聲明:焊材網轉載作品均注明出處,本網未注明出處和轉載的,是出于傳遞更多信息之目的,并不意味 著贊同其觀點或證實其內容的真實性。如轉載作品侵犯作者署名權,或有其他諸如版權、肖像權、知識產權等方面的傷害,并非本網故意為之,在接到相關權利人通知后將立即加以更正。聯系電話:0571-87774297。
0571-87774297  
主站蜘蛛池模板: 中超| 平顶山市| 江永县| 仪陇县| 吉安县| 绍兴市| 安义县| 屏南县| 浪卡子县| 安新县| 那曲县| 宁阳县| 资溪县| 淮南市| 南投县| 大渡口区| 东至县| 梨树县| 民乐县| 靖宇县| 米脂县| 三原县| 乐至县| 西乡县| 新巴尔虎左旗| 高青县| 平谷区| 仁怀市| 石阡县| 金秀| 临夏县| 柳河县| 泰来县| 安溪县| 凯里市| 滨州市| 澜沧| 华宁县| 平阴县| 巢湖市| 辽宁省|