国产三级伦理在线,久久久久黄久久免费漫画,成人国产精品日本在线,欧美美最猛性xxxxxx

    AT71YM2CL2014-BA0行李追蹤及安全性
    發布者:上海凌亮光電科技有限公司  發布時間:2023-02-03 13:50:48  訪問次數:182

    1 Synchronization Mode Four different modes may be defined under user control. The TRIG1 and TRIG2 signals may be used to trigger external events and to control the integration time. The Master clock is either external or internal clock

    2 Free Run Mode with Integration Time Setting The integration and readout periods start automatically and immediately after the previous period. The read-out time depends on pixel number and pixel rate.

    3 Trigger and Integration Time Controlled by One Input The integration period starts immediately after the falling edge of TRIG1 input signal, stops immediately after the rising edge of TRIG1 input signal, and is immediately followed by a readout period. The readout time depends on pixel number and pixel rate

    4 Trigger and Integration Time Controlled by Two Inputs TRIG2 rising edge start the integration period. TRIG1 rising edge stop the integration period. This period is immediately followed by a readout period.

    5. Timing Diagram Note: CLK_IN input frequency must be in the range 5 to 60 MHz. Out of this range, the performances may be decreased. In case of multi-cameras synchronization (means more than one camera on one acquisition board): ? the "master" camera will provide DATA, STROBE and LVAL signals to the acquisition board. The others will only provide DATA. ? the external clock CLK_IN must be input on each cameras to guaranty perfect data synchronization. ? the trigger(s) input (TRIG1 and/or TRIG2) must be input on each cameras. It is recommended to synchronize the rising edge of these signals on the CLK_IN falling edge. ? cables must be balanced between each cameras (same quality, same length) to ensure perfect cameras synchronization. ? the CLK_IN frequency must be equal to the two CCD register frequency. It means that the user shall use either H=2 (2 taps at CLK_IN data rate) or H=10 (1 tap at 2xCLK_IN data rate). Using H=1 clock mode will provide LVAL jitter on the "slave" camera. ? Only "triggered and integration time controlled" (M=3 or M=4) can be used. These modes ensure perfect readout phase starting for each cameras. tp td Internal Clock or CLK_IN CLK_IN (case H = 10) LVAL STROBE DATA First valid pixel Last valid pixel

免責聲明:焊材網轉載作品均注明出處,本網未注明出處和轉載的,是出于傳遞更多信息之目的,并不意味 著贊同其觀點或證實其內容的真實性。如轉載作品侵犯作者署名權,或有其他諸如版權、肖像權、知識產權等方面的傷害,并非本網故意為之,在接到相關權利人通知后將立即加以更正。聯系電話:0571-87774297。
0571-87774297  
主站蜘蛛池模板: 梧州市| 西平县| 于田县| 金昌市| 视频| 临泽县| 博罗县| 庄河市| 清徐县| 仙桃市| 遂宁市| 平凉市| 本溪市| 建阳市| 永靖县| 郯城县| 武川县| 云林县| 肇州县| 始兴县| 富蕴县| 砀山县| 桦川县| 横峰县| 抚松县| 肥城市| 环江| 汤原县| 都匀市| 大余县| 腾冲县| 洛扎县| 彰武县| 鄂托克旗| 屯门区| 宁强县| 常德市| 岗巴县| 大余县| 濮阳市| 宝山区|