商鋪名稱：清河縣安泰焊接材料有限公司
聯系人：王經理（先生）
聯系手機：
固定電話：
企業郵箱：wanhonghanjie@163.com
聯系地址：河北省清河縣經濟開發區
郵編：058400
聯系我時，請說是在焊材網上看到的，謝謝！
黔東南飛機牌L325銀焊條 電話
| Category | Trade-mark | Specification | Melting | Chemical | Application | Equivalent |
| Copper 銅鋅 | L103 | Wire & rod | 885-888 | Cu54 Zn Rem. | Brazing of copper, bronze and steel, subjected to low load. | 黔東南飛機牌L325銀焊條 電話 |
| L104 | Foil | 890-930 | Cu57 Mn2 | Brazing of carbide cutting tool. | ||
| Copper 銅磷 | L201 | Cast rod, wire & rod, powder | 710-800 | P7 Cu Rem. | Brazing of copper and copper alloys. | BCuP-2 |
| L204 | Cast rod, wire | 640-815 | P5 Ag15 | Brazing of copper, copper alloys, silver and molybdenum etc. | BCuP-5 | |
| L205 | Cast rod, wire & rod, powder | 640-800 | P6 Ag5 | Brazing of copper and copper alloys. | BCuP-3 | |
| L207 | Cast rod, wire & rod | 640-770 | P7 Ag5 | Brazing of copper and copper alloys. | BCuP-7 | |
| L209 | Cast rod, wire | 684-710 | P7 Ag2 | Brazing of copper and copper alloys. | BCuP-6 | |
| Silver 銀基 | L302 | Wire & rod | 745-775 | Ag25 Cu40 | Brazing of copper, copper alloys, steel and stainless steel etc. | 此外，對于藥皮中含有多量鐵粉的焊條，可以稱為鐵粉焊條。這時，按照相應焊條藥皮的主要成分，又可分為鐵粉鈦型、鐵粉鈦鐵礦型、鐵粉氧化鐵型、鐵粉低氫型等，構成了鐵粉焊條系列。 |
| L303 | Wire & rod | 660-725 | Ag45 Cu30 | Brazing of copper, copper alloys, steel and stainless steel etc. | BAg-5 | |
| L303F | Flux coated rod | 660-725 | Ag45 Cu30 | L303 coated with flux, the same application as L303. | BAg-5 | |
| L304 | Foil | 690-775 | Ag50 Cu34 | Brazing of copper, copper alloys and steel etc. | BAg-6 | |
| L308 | Wire & rod | 779-780 | Ag72 Cu Rem. | Brazing of copper and nickel under vacuum or reducing protective atmosphere. | BAg-8 | |
| L312 | Wire & rod | 595-605 |
| Brazing of copper, copper alloys, steel and stainless steel etc. | ||
| L313 | Wire & rod | 625-635 |
| Brazing of copper, copper alloys, steel and stainless steel etc. | BAg-1a | |
| L321 | Wire & rod 絲 | 615-650 |
| Brazing of copper, copper alloys, steel and stainless steel etc. | BAg-7 | |
| L323 | Wire & rod | 665-755 |
| Brazing of copper, copper alloys, steel and stainless steel etc. | ||
| L325 | Wire & rod | 645-685 |
| Brazing of copper, copper alloys, steel and stainless steel etc. | BAg-36 | |
| L326 | Wire & rod | 650-720 |
| Brazing of copper, copper alloys, steel and stainless steel etc. | BAg-34 | |
| Aluminum base 鋁基 | L400 | Cast rod, wire & rod | 577-582 | Si11.5 | Brazing of aluminum and aluminum alloys. | BAlSi-4 |
| L401 | Cast rod | 525-535 | Si5 Cu28 | Brazing of aluminum and aluminum alloys. | 六、藥皮在焊接過程中起著極為重要的作用。若采用無藥皮的光焊條焊接，則在焊接過程中，空氣中的氧和氮會大量侵入熔化金屬，將金屬鐵和有益元素碳、硅、錳等氧化和氮化形成各種氧化物和氮化物，并殘留在焊縫中，造成焊縫夾渣或裂紋。而熔入熔池中的氣體可能使焊縫產生大量氣孔，這些因素都能使焊縫的機械性能（強度、沖擊值等）大大降低，同時使焊縫變脆。此外采用光焊條焊接，電弧很不穩定，飛濺嚴重，焊縫成形很差。 | |
| Tin lead 錫鉛 | L600 | Wire & rod | 183-185 | Sn60 Sb≤0.8 | Soldering of fusible metals and heat-treated part. | 60Sn |
| L601 | Wire & rod | 183-227 | Sn18 Sb2 | Soldering of copper, copper alloys and galvanized iron plain sheet. | 18Sn | |
| L602 | Wire & rod | 183-256 | Sn30 Sb2 | Soldering of copper, brass, copper alloys and galvanized iron plain sheet. | 30Sn | |
| L603 | Wire & rod | 183-235 | Sn40 Sb2 | Soldering of copper, copper alloys, steel and zinc parts. | 40Sn | |
| L604 | Wire & rod | 183-222 | Sn90 Sb≤0.15 | Soldering of copper and steel for food and medicine field. | 90Sn | |
| L605 | Wire & rod | 232-240 | Ag5 Sn95 | Soldering of copper and steel for electrical and food field. | 焊條就是涂有藥皮的供焊條電弧焊使用的熔化電極，它是由藥皮和焊芯兩部分組成的。在焊條前端藥皮有45°左右的倒角，這是為了便于引弧。在尾部有一段裸焊芯，約占焊條總長1/16，便于焊鉗夾持并有利于導電。焊條的直徑實際上是指焊芯直徑）通常為2、2.5、3.2或3、4、5或6mm等幾種規格，最常用的是小3.2、小4、小5三種，其長度“L”一般在200～550 mm之間。 | |
| L608 | Wire & rod | 295-305 | Sn5.5 Ag2.5 | Soldering of copper, copper alloys, steel and stainless steel. | 焊條牌號的編制方法 | |
| Nickel base 鎳基 | L702 | Powder | 970-1000 | Cr7 B3 Si4 | Brazing of stainless steel under vacuum or protective atmosphere. | BNi-2 |
黔東南飛機牌L325銀焊條 電話
（8）藥皮類型：石墨型 電源種類：直流或交流 主要特點：藥皮中含有多量石墨，通常用于鑄鐵或堆焊焊條。采用低碳鋼焊芯時，焊接工藝性能較差，飛濺較多，煙霧較大，熔渣少，適于平焊。采用有色金屬焊芯時，能改善其工藝性能，但電流不易過大。
