商鋪名稱：清河縣安泰焊接材料有限公司
聯系人：王經理（先生）
聯系手機：
固定電話：
企業郵箱：wanhonghanjie@163.com
聯系地址：河北省清河縣經濟開發區
郵編：058400
聯系我時，請說是在焊材網上看到的，謝謝！
文山州飛機牌L321銀焊條多少錢
| Category | Trade-mark | Specification | Melting | Chemical | Application | Equivalent |
| Copper 銅鋅 | L103 | Wire & rod | 885-888 | Cu54 Zn Rem. | Brazing of copper, bronze and steel, subjected to low load. | 文山州飛機牌L321銀焊條多少錢 |
| L104 | Foil | 890-930 | Cu57 Mn2 | Brazing of carbide cutting tool. | ||
| Copper 銅磷 | L201 | Cast rod, wire & rod, powder | 710-800 | P7 Cu Rem. | Brazing of copper and copper alloys. | BCuP-2 |
| L204 | Cast rod, wire | 640-815 | P5 Ag15 | Brazing of copper, copper alloys, silver and molybdenum etc. | BCuP-5 | |
| L205 | Cast rod, wire & rod, powder | 640-800 | P6 Ag5 | Brazing of copper and copper alloys. | BCuP-3 | |
| L207 | Cast rod, wire & rod | 640-770 | P7 Ag5 | Brazing of copper and copper alloys. | BCuP-7 | |
| L209 | Cast rod, wire | 684-710 | P7 Ag2 | Brazing of copper and copper alloys. | BCuP-6 | |
| Silver 銀基 | L302 | Wire & rod | 745-775 | Ag25 Cu40 | Brazing of copper, copper alloys, steel and stainless steel etc. | |
| L303 | Wire & rod | 660-725 | Ag45 Cu30 | Brazing of copper, copper alloys, steel and stainless steel etc. | BAg-5 | |
| L303F | Flux coated rod | 660-725 | Ag45 Cu30 | L303 coated with flux, the same application as L303. | BAg-5 | |
| L304 | Foil | 690-775 | Ag50 Cu34 | Brazing of copper, copper alloys and steel etc. | BAg-6 | |
| L308 | Wire & rod | 779-780 | Ag72 Cu Rem. | Brazing of copper and nickel under vacuum or reducing protective atmosphere. | BAg-8 | |
| L312 | Wire & rod | 595-605 |
| Brazing of copper, copper alloys, steel and stainless steel etc. | 1)碳(C)碳是鋼中的主要合金元素，當含碳量增加時，鋼的強度、硬度明顯提高，而塑性降低。在焊接過程中，碳起到一定的脫氧作用，在電弧高溫作用下與氧發生化合作用，生成一氧化碳和二氧化碳?xì)怏w，將電弧區和熔池周圍空氣排除，防止空氣中的氧、氮有害氣體對熔池產生的不良影響，減少焊縫金屬中氧和氮的含量。若含碳量過高，還原作用劇烈，會引起較大的飛濺和氣孔。考慮到碳對鋼的淬硬性及其對裂紋敏感性增加的影響，低碳鋼焊芯的含碳量一般為0. 1%。 | |
| L313 | Wire & rod | 625-635 |
| Brazing of copper, copper alloys, steel and stainless steel etc. | BAg-1a | |
| L321 | Wire & rod 絲 | 615-650 |
| Brazing of copper, copper alloys, steel and stainless steel etc. | BAg-7 | |
| L323 | Wire & rod | 665-755 |
| Brazing of copper, copper alloys, steel and stainless steel etc. | ||
| L325 | Wire & rod | 645-685 |
| Brazing of copper, copper alloys, steel and stainless steel etc. | BAg-36 | |
| L326 | Wire & rod | 650-720 |
| Brazing of copper, copper alloys, steel and stainless steel etc. | BAg-34 | |
| Aluminum base 鋁基 | L400 | Cast rod, wire & rod | 577-582 | Si11.5 | Brazing of aluminum and aluminum alloys. | BAlSi-4 |
| L401 | Cast rod | 525-535 | Si5 Cu28 | Brazing of aluminum and aluminum alloys. | 3)硅(Si )硅也是一種較好的合金劑，在鋼中加入適量的硅能提高鋼的屈服強度、彈性及抗酸性能；若含量過高，則降低塑性和韌性。在焊接過程中，硅也具有較好的脫氧能力，與氧形成二氧化硅，但它會提高渣的粘度，易促進非金屬夾雜物生成。 | |
| Tin lead 錫鉛 | L600 | Wire & rod | 183-185 | Sn60 Sb≤0.8 | Soldering of fusible metals and heat-treated part. | 60Sn |
| L601 | Wire & rod | 183-227 | Sn18 Sb2 | Soldering of copper, copper alloys and galvanized iron plain sheet. | 18Sn | |
| L602 | Wire & rod | 183-256 | Sn30 Sb2 | Soldering of copper, brass, copper alloys and galvanized iron plain sheet. | 30Sn | |
| L603 | Wire & rod | 183-235 | Sn40 Sb2 | Soldering of copper, copper alloys, steel and zinc parts. | 40Sn | |
| L604 | Wire & rod | 183-222 | Sn90 Sb≤0.15 | Soldering of copper and steel for food and medicine field. | 90Sn | |
| L605 | Wire & rod | 232-240 | Ag5 Sn95 | Soldering of copper and steel for electrical and food field. | ||
| L608 | Wire & rod | 295-305 | Sn5.5 Ag2.5 | Soldering of copper, copper alloys, steel and stainless steel. | （9）藥皮類型：鹽基型 電源種類：直流 主要特點： 藥皮中含多量氯化物和氟化物，主要用于鋁及鋁合金焊條。吸潮性強，焊前要烘干。藥皮熔點低，熔化速度快。采用直流電源，焊接工藝性較差，短弧操作，熔渣有腐蝕性，焊后需用熱水清洗。 | |
| Nickel base 鎳基 | L702 | Powder | 970-1000 | Cr7 B3 Si4 | Brazing of stainless steel under vacuum or protective atmosphere. | BNi-2 |
文山州飛機牌L321銀焊條多少錢
焊條就是涂有藥皮的供焊條電弧焊使用的熔化電極，它是由藥皮和焊芯兩部分組成的。在焊條前端藥皮有45°左右的倒角，這是為了便于引弧。在尾部有一段裸焊芯，約占焊條總長1/16，便于焊鉗夾持并有利于導電。焊條的直徑實際上是指焊芯直徑）通常為2、2.5、3.2或3、4、5或6mm等幾種規格，最常用的是小3.2、小4、小5三種，其長度“L”一般在200～550 mm之間。
